COMPARATIVE ANALYSIS OF THE RESULTSOF AN EXPERIMENTAL STUDY WITH BASIC EQUIPMENT AND A SPECIALLY MADE ONE TOTHE INSIZE ISR - C002 ROUGHNESS TESTER

Authors

  • Kliment Georgiev Technical University of Sofia, branch Plovdiv, Faculty of Mechanical Engineering; Department: Mechanical and Instrument Engineering (BG)
  • Pavlina Katsarova Technical University of Sofia, branch Plovdiv, Faculty of Mechanical Engineering; Department: Mechanical and Instrument Engineering (BG)

DOI:

https://doi.org/10.17770/etr2024vol3.8106

Keywords:

additive printing, basic equipment, comparative analysis, experiments, fixture, measurement System Analysis (MSA), roughness tester, surface roughness

Abstract

The present research presents a comparative analysis between experiments conducted with basic equipment for a portable INSIZE ISR - C002 roughness tester and a specially made for the purpose attachment to the device. An analysis is made of the proposed basic device for working with a portable roughness tester INSIZE ISR - C002, and its shortcomings have been determined. In order to facilitate the operator's work with the device and obtain more accurate results, a special device is developed. It is designed using CAD/CAM products and manufactured using additive printing (3D printing). The additive printing technology used reduces its cost. The manufactured device is analyzed and its advantages and disadvantages are determined. Experiments are conducted with both devices and a comparative analysis of the obtained results is made. An analysis of the measurement system (MSA) is made, through which the results of the conducted experiments were analyzed. The comparative analysis shows a number of advantages of the new device compared to the basic one, which provide a basis for the formulated conclusions and recommendations.

 

Supporting Agencies
The author/s would like to thank the Research and Development Sector at the Technical University of Sofia for the financial support

Downloads

Download data is not yet available.

References

Whitehouse, D. J. (1997). Surface metrology. Measurement science and technology, 8(9), 955.

G. Eason, B. Noble, and I. N. Sneddon, “On certain integrals of Lipschitz-Hankel type involving products of Bessel functions,” Phil. Trans. Roy. Soc. London, vol. A247, pp. 529–551, April 1955.

J. Clerk Maxwell, A Treatise on Electricity and Magnetism, 3rd ed., vol. 2. Oxford: Clarendon, 1892, pp.68–73.

Hamed, M., Zedan, Y., Samuel, A. M., Doty, H. W., & Samuel, F. H. (2019). Milling parameters of Al-Cu and Al-Si cast alloys. The International Journal of Advanced Manufacturing Technology, 104, 3731-3743.

Gadelmawla, E. S., Koura, M. M., Maksoud, T. M., Elewa, I. M., & Soliman, H. H. (2002). Roughness parameters. Journal of materials processing Technology, 123(1), 133-145.

Asakura, T. (1978). Surface roughness measurement. Speckle metrology, 11-49.

Measurement systems analysis (MSA), Reference Manual, Fourth Edition, Copyright 2010 Chrysler Group LLC, Ford Motor Company, General Motors Corporation, ISBN#: 978-1-60-534211-5

Dian, M., & Hodinář, L. (2018). The GRR a Fundamental Tool for Dealing with Measurement System Variability. Manufacturing Technology, 18(1), 29-34.

Portable roughness tester INSIZE ISR – C002, available at: https://www.grainger.com/product/INSIZE-Handheld-Surface-Roughness-463L43, 15.02.2024.

Coppola, B., Cappetti, N., Di Maio, L., Scarfato, P., & Incarnato, L. (2018). 3D printing of PLA/clay nanocomposites: Influence of printing temperature on printed samples properties. Materials, 11(10), 1947.

Hristov, M. H. (2023, September). SPC as an Instrument for Implementation and MSA as an Instrument for Evaluation of Non-Linear Object Based Temperature Compensation into Shop Floor CMM. In 2023 15th Electrical Engineering Faculty Conference (BulEF) (pp. 1-9). IEEE.

Qiu P., Introduction to Statistical Process Control, 2014 by Taylor & Francis Group, LLC, ISBN-13: 978-1-4822-2041-4 (eBook - PDF)

https://www.aiag.org/

Downloads

Published

2024-06-22

Issue

Vol. 3 (2024): Environment. Technology. Resources. Proceedings of the 15th International Scientific and Practical Conference. Volume 3

Section

Engineering Sciences and Production Technologies

License

Copyright (c) 2024 Kliment Georgiev, Pavlina Katsarova

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

How to Cite

[1]
K. Georgiev and P. Katsarova, “COMPARATIVE ANALYSIS OF THE RESULTSOF AN EXPERIMENTAL STUDY WITH BASIC EQUIPMENT AND A SPECIALLY MADE ONE TOTHE INSIZE ISR - C002 ROUGHNESS TESTER”, ETR, vol. 3, pp. 58–64, Jun. 2024, doi: 10.17770/etr2024vol3.8106.