RIGID CONNECTION WITH GRANITE CHIPS IN THE TIMBER-CONCRETE COMPOSITE
DOI:
https://doi.org/10.17770/etr2021vol3.6552Keywords:
adhesive connection, bending test, carbon fibre reinforced plastic, finite element method, glued connection, rigid connection, timber-concrete composite, wood-concrete compositeAbstract
Timber-concrete composite panels enables to combine advantages of pure timber and pure concrete panels in one structural member especially in the case, when the rigid timber-concrete connection is provided. The effectiveness of timber and concrete use and load-carrying capacity of the timber-concrete composite panels will grow in the case. The new concept of rigid timber to concrete connection was developed by the using of the granite chips as the keys to provide high quality of the glued connection. Behaviour of the timber-concrete composite panels were investigated by finite element method and laboratorian experiment. Three timber-concrete composite panels in combination with carbon fibre reinforced plastic composite tapes in the tension zone with the span 1.8 m were statically loaded till the failure by the scheme of three-point bending. One specimen was produced by dry method, by gluing together cross-laminated timber panel and prefabricated concrete panel. Timber-concrete connection of the other two specimens was provided by the granite chips, which were glued on the surface of the cross-laminated timber by epoxy, and then wet concrete was placed. Dimensions of the crushed granite pieces changes within the limits from 16 to 25 mm. The current study focuses on determining the effect of the use of granite chips for timber-concrete composite panels with adhesive connection between layers. The effect of the use of granite chips in rigid connection is determined by comparison of mid-span displacements and level of failure load of the two variants of the timber-concrete composite panels. Three-dimensional finite element models of timber-concrete composite with rigid connection was developed and validated by experiment data. Obtained results shown, that the use of the granite chips in rigid timber to concrete connection allow to make a quality rigid connection. Possibility to increase by 28% level of failure load of the timber-concrete composite panels by the adding of granite chips was stated. Maximal vertical mid-span displacements of the panels decrease about 3.8 times at the same time.
Downloads
References
T. Tannert, A. Gerber and T. Vallee, "Hybrid adhesively bonded timber-concrete-composite floors," International Journal of Adhesion and Adhesives, vol. 97, Nr. 102490, 2020. DOI: 10.1016/j.ijadhadh.2019.102490
M. Fragiacomo, A. Gregori, J. Xue, C. Demartino and M. Toso, "Timber-concrete composite bridges: Three case studies," Journal of Traffic and Transportation Engineering (English Edition), vol. 5, pp. 429-438, 2018. DOI: 10.1016/j.jtte.2018.09.001
J. Kanocz, V Bajzecerova and S. Steller, "Timber – concrete composite elements with various composite connections. Part 1: screwed connection," Wood Research, vol. 58, pp. 555–570, 2013.
J. Kanocz and V Bajzecerova, "Timber – concrete composite elements with various composite connections. Part 3: adhesive connection," Wood Research, vol. 60, pp. 939–952, 2015.
M. Brunner, M. Romer and M. Schnüriger, "Timber-concrete-composite with an adhesive connector (wet on wet process)," Materials and Structures/Materiaux et Constructions, vol. 40, pp. 119–126, 2007. DOI: 10.1617/s11527-006-9154-4
J.H. Negrao, F.M. Oliveira and C.L. Oliveira, "Investigation on timber-concrete glued composites," In: 9th World Conference on Timber Engineering (WCTE 2006). Portland, Oregon, USA, 2006.
M. Al Ali, V. Bajzecerova and V. Kvocak, "Design methods of timber-concrete composite ceiling structure," Magazine of Civil Engineering, vol. 73(5), pp. 88–95, 2017. DOI: 10.18720/MCE.73.8
V. Mironovs, A. Tatarinov, and S. Gorbacova, "Expanding Application of Perforated Metal Materials," In: Construction and Architecture IOP Conference Series: Materials Science and Engineering, vol. 251(1), Nr. 012027, 2017. DOI: 10.1088/1757-899X/251/1/012027
M. V. Gravit, D. Serdjuks, A. V. Bardin, V. Prusakov and K. Buka-Vaivade, "Fire design methods for structures with timber framework," Magazine of Civil Engineering, vol. 85, pp. 92-106, 2019. DOI: 10.18720/MCE.85.8
M. N. Kirsanov, "Lower estimate of the fundamental frequency of natural oscillations of a truss with an arbitrary number of panels," Vestnik MGSU, vol. 14(7), pp. 844-851, 2019. DOI: 10.22227/1997-0935.2019.7.844-851
K. Buka-Vaivade, D. Serdjuks, V. Goremikins, A. Vilguts and L Pakrastins, "Experimental verification of design procedure for elements from cross-laminated timber," Procedia Engineering, vol. 172, pp. 1212–1219, 2017. DOI: 10.1016/j.proeng.2017.02.142
A. Dias, J. Schänzlin and P. Dietsch, "Design of timber-concrete composite structures", Aachen: Shaker Verlag GmbH, 2018.
R. Vasiljevs, D. Serdjuks, K. Buka-Vaivade, A. Podkoritovs and N. Vatin, "Load-carrying capacity of timber-concrete composite panels," Magazine of Civil Engineering, vol. 93, pp. 60-70, 2020. DOI: 10.18720/MCE.93.6
R. Vasiljevs, D. Serdjuks, J. Gerasimova, K. Buka-Vaivade and A. Orhun Erüz, "Behaviour of Timber-Concrete Joints in Hybrid Members Subjected to Flexure," IOP Conference Series: Materials Science and Engineering, vol. 660, Nr. 012050, 2019. DOI: 10.1088/1757-899X/660/1/012050
A. Skincs, D. Serdjuks, K. Buka-Vaivade, V. Goremikins and A.Y. Mohamed, "Steel and composite tapes in timber to concrete joint," Lecture Notes in Civil Engineering, vol. 141, pp. 68–79, 2021.
J. Gerasimova, "Testing of design method for hybrid elements subjected to flexure," M.S. thesis, Riga Technical university, Riga, Latvia, 2017.
R. Vasiljevs, "Load-carrying Capacity Analyse for Hybrid Composite Member," M.S. thesis, Riga Technical university, Riga, Latvia, 2018.
